For Sale TFS Twisted wedge heads

Selling a set of twisted wedge heads, also a set of ford racing 1.72 roller rockers stud mount.
Heads have about 800 miles since NMRA Champion Rich Groh performed a valve job, installed new inconnel exhaust valves, tripple valve spring for solid roller cam good for at least .650lift. Titanium retainers and keepers. Heads are 58cc chambers and have mild cleanup on intake and exhaust gasket matched to felpro 1415 exhaust and I forget the intake but I can find out that gasket number too when I go home.
Email me if interested steedafied@aol.com
I also and selling a 74 351w block $250

Going in another new direction with the stang? Or are you putting it back to stock

Just going bigger. Got a smoking deal on a provin setup, just needs a freshen up and put back together.
Will be selling my solid roller .650lift turbo cam and linkbar lifters too. New cams bigger. And tfs-r 351w intake. Prolly ati dampner and jw the wheel too. Nuetral balance.
Also cometic head gaskets 4 sale.

First pass off the trailer, havent been down the track in close to two years.
.020
1.337
3.487
5.294
136.07 mph
6.852
8.175
169.85 mph

Time slip and vid or it didn't happen

The B.S. flag has been raised.

That's the car my new engine is from. It was on drag radials with a 101mm and 16psi.
It went 8.8's on 12psi with a 88 or 91mm on pump gas in hotrod magazine in 06.
Its a truestreet car.

My car went 10.1 on 12psi letting off cause too loose a converter on the shitty tune last year fyi. Got timeslip if u wanna see that.

Awe shit, is this that supra thread all over again where you start claiming your car runs that because another car did? This is even worse because its a different chasis and only the engine is the same!

I didn't know you got it to the track Vlamis, ::sniff sniff:: no call?

Damn Dale, did I start a thread like that in the past?

Hey now. I don't know if we're referring to my car, but it actually ran a 10.6@125 with the previous owner. Same car, not different car with similar setup.

would those work as an even swap into the 3000GT, i have been on the lookout to give the red dragon a little bit more power to the front tires.

Hey I'm not claiming my car is gonna do bottom 8's with this engine. All I'm saying is I know that my suspension works and that the engine I bought went 8.1 at 170mph on 16psi on d/r tires and weighed 3500lbs with driver.
Its not an engine like one or anything like that. This is the engine intake to oil pan. It was even a carbed setup. Which I will be converting the intake to efi and putting a elbow on it with a big tbody.
Obviously I will be putting my turbos on it and probably going bigger on them in the near future. But expect some high 8's by next spring.

Also selling my tfs r 351w intake $475 polished. Bbk 75mm tbody for 94-95 and edelbrock elbow which is powder coated with egr blocked off(welded off tig) $150 for tbody and elbow.
Ford racing 1.72 rocker for $150.
Tfs tw heads for $1050 (need 1 new intake valve) titanium retainers and keepers and .650+ lift tripple valve springs and inconnel exhaust valves 800 miles since rebuilt. 58cc chambers. 2.02 intake valve 1.60 exhaust.
More parts will be for sale soon.
Lake wood 50/50 rear shocks and d&d rear coilover kit $300

Enjoy my new sig bitches.

http://videos.streetfire.net/video/1200rwh...ng-a_680298.htm
http://videos.streetfire.net/video/1-BAD-S...TANG_681843.htm